Assembler errors with project for a Nios

[Joost van der Weerden]

>
>Hi,
>
>I wrote a very large project for a Nios processor (Altera) When I build
>that project (compile, link and assemble) everything goes right the first
>times. When I add some more code to it and then try to assemble i'll get
>the following messages:
>
>[nios]$ nb -cc -mmax-address=0x1fffff main.c.c
>                                       ^^^^^^^^^
>                                                 should be main.c.

I'm sorry that's just a type mistake, I build it actually with main.c , so 
that isn't the problem


>--------------------
>Beginning Build
>--------------------
>
>Sources:
>main.c
>
>
># 2002.06.05 10:44:44 (*) nios-elf-gcc -I ../inc -I ../../inc -I 
>../../../inc -I ../../../../inc -I ../../../../../inc -g -O2 
>-mmax-address=0x1fffff -m32 main.c -o main.c.o -c
>C:\Cygwin\/tmp/cceJZ3Uc.s: Assembler messages:
>C:\Cygwin\/tmp/cceJZ3Uc.s:243: Error: Value of 65636 too large for field 
>of 2 bytes at 248
>C:\Cygwin\/tmp/cceJZ3Uc.s:244: Error: Value of 65636 too large for field 
>of 2 bytes at 250
>C:\Cygwin\/tmp/cceJZ3Uc.s:245: Error: Value of 65636 too large for field 
>of 2 bytes at 252
>C:\Cygwin\/tmp/cceJZ3Uc.s:34811: Error: Value of 65572 too large for field 
>of 2 bytes at 50356
>C:\Cygwin\/tmp/cceJZ3Uc.s:34812: Error: Value of 65572 too large for field 
>of 2 bytes at 50358
>C:\Cygwin\/tmp/cceJZ3Uc.s:34813: Error: Value of 65572 too large for field 
>of 2 bytes at 50360
>C:\Cygwin\/tmp/cceJZ3Uc.s:42130: Error: Value of 65636 too large for field 
>of 2 bytes at 60036
>C:\Cygwin\/tmp/cceJZ3Uc.s:42131: Error: Value of 65636 too large for field 
>of 2 bytes at 60038
>C:\Cygwin\/tmp/cceJZ3Uc.s:42132: Error: Value of 65636 too large for field 
>of 2 bytes at 60040
>These are the lines which they refers to:
>243:    pfx %hi(ACQ_Resort_Functioning@h)
>244:    movi %g1, %lo(ACQ_Resort_Functioning@h)
>245:    movhi %g1, %xlo(ACQ_Resort_Functioning@h)
>34811:  pfx %hi(SYS_Load_Software_Mode@h)
>34812:  movi %o0, %lo(SYS_Load_Software_Mode@h)
>34813:  movhi %o0, %xlo(SYS_Load_Software_Mode@h)
>42130:  pfx %hi(ACQ_Resort_Functioning@h)
>42131:  movi %g1, %lo(ACQ_Resort_Functioning@h)
>42132:  movhi %g1, %xlo(ACQ_Resort_Functioning@h)
>
>To build the project I use the following command line: "nios-build -cc 
>-mmax-address=0x1FFFFF main.c"
>nios-build is a script to compile, link and assemble with the options for 
>nios. It also uses -O2 and -m32
>When i remove some lines everything is ok. How can I bypass this problem?
>
>regards Joost
>