Ping: Re: [PATCH 10/11][RS6000] Migrate reduction optabs to reduc_..._scal

Alan Lawrence alan.lawrence@arm.com
Thu Dec 11 15:59:00 GMT 2014


So I'm afraid I'm not going to get involved in a discussion about 
CANNOT_CHANGE_MODE_CLASS on RS6000, and what you might want to do there - sorry, 
but I don't think I can really contribute anything there. However, I *am* trying 
to migrate all platforms off the old reduc_xxx optabs to the new version 
producing a scalar.

Hence, can I ping the attached patch (which is just a simple combination of the 
previously-posted patch + snippet)? No regressions on gcc112.fsffrance.org.

This works in exactly the same way as the old code path, with a second insn to 
pull the scalar result out of the reduction, just as the expander would have 
done (or the bitfieldref before that), and avoiding the v2df combine pattern 
(again, as previously).

gcc/ChangeLog:

     * config/rs6000/altivec.md (reduc_splus_<mode>): Rename to...
     (reduc_plus_scal_<mode>): ...this, add rs6000_expand_vector_extract.
     (reduc_uplus_v16qi): Remove.

     * config/rs6000/vector.md (VEC_reduc_name): change "splus" to "plus"
     (reduc_<VEC_reduc_name>_v2df): Remove.
     (reduc_<VEC_reduc_name>_scal_v2df): New.
     (reduc_<VEC_reduc_name>_v4sf): Rename to...
     (reduc_<VEC_reduc_name>_scal_v4sf): ...this, wrap VEC_reduc in a
     vec_select of element 3, add scratch register.




> Have run check-gcc on gcc110.fsffrance.org (powerpc64-unknown-linux-gnu) using this snippet on top of original patch; no regressions.
> 
> 
> Alan Lawrence wrote:
> 
>     So I'm no expert on RS6000 here, but following on from Segher's observation about the change in pattern...so the difference in 'expand' is exactly that, a vsx_reduc_splus_v2df followed by a vec_extract to DF, becomes a vsx_reduc_splus_v2df_scalar - as I expected the combiner to produce by combining the two previous insns.
> 
> 
>     However, inspecting the logs from -fdump-rtl-combine-all, *without* my patch, when the combiner tries to put those two together, I see:
> 
> 
>     Trying 30 -> 31:
>     Failed to match this instruction:
>     (set (reg:DF 179 [ stmp_s_5.7D.2196 ])
>          (vec_select:DF (plus:V2DF (vec_select:V2DF (reg:V2DF 173 [ vect_s_5.6D.2195 ])
>                      (parallel [
>                              (const_int 1 [0x1])
>                              (const_int 0 [0])
>                          ]))
>                  (reg:V2DF 173 [ vect_s_5.6D.2195 ]))
>              (parallel [
>                      (const_int 1 [0x1])
>                  ])))
> 
>     That is, it looks like combine_simplify_rtx has transformed the (vec_concat (vec_select ... 1) (vec_select ... 0)) from the vsx_reduc_plus_v2df insn, into a single vec_select, which does not match the vsx_reduc_plus_v2df_scalar insn.
> 
> 
>     So despite the comment (in vsx.md):
> 
>     ;; Combiner patterns with the vector reduction patterns that knows we can get
>     ;; to the top element of the V2DF array without doing an extract.
> 
>     It looks like the code generation prior to my patch, considered better, was because the combiner didn't actually use the pattern?
> 
> 
>     In that case whilst you may want to dig into register allocation, cannot_change_mode_class, etc., for other reasons, I think the best fix for migrating to reduc_plus_scal... is simply to avoid using the "Combiner" patterns and just emit two insns, the old pattern followed by a vec_extract. The attached snippet does this (I won't call it a patch yet, and it applies on top of the previous patch - I went the route of calling the two gen functions rather than copying their RTL sequences, but could do the latter if that were preferable???), and restores code generation to the original form on your example above; it bootstraps OK but I'm still running check-gcc on the Compile Farm...
> 
> 
>     However, again on your example above, I note that if I *remove* the reduc_plus_scal_v2df pattern altogether, I get:
> 
> 
>     .sum:
>              li 10,512        # 52   *movdi_internal64/4     [length = 4]
>              ld 9,.LC2@toc(2)         # 20   *movdi_internal64/2     [length = 4]
>              xxlxor 0,0,0     # 17   *vsx_movv2df/12 [length = 4]
>              mtctr 10         # 48   *movdi_internal64/11    [length = 4]
>              .align 4
>     .L2:
>              lxvd2x 12,0,9    # 23   *vsx_movv2df/2  [length = 4]
>              addi 9,9,16      # 25   *adddi3_internal1/2     [length = 4]
>              xvadddp 0,0,12   # 24   *vsx_addv2df3/1 [length = 4]
>              bdnz .L2         # 47   *ctrdi_internal1/1      [length = 4]
>              xxsldwi 12,0,0,2         # 30   vsx_xxsldwi_v2df        [length = 4]
>              xvadddp 1,0,12   # 31   *vsx_addv2df3/1 [length = 4]
>              nop      # 37   *vsx_extract_v2df_internal2/1   [length = 4]
>              blr      # 55   return  [length = 4]
> 
>     this is presumably using gcc's scalar reduction code, but (to my untrained eye on powerpc!) it looks even better than the first form above (the same in the loop, and in the reduction, an xxpermdi is replaced by a nop !)...
> 
> 
>     --Alan
> 
> 
>     Segher Boessenkool wrote:
> 
>         On Mon, Nov 10, 2014 at 05:36:24PM -0500, Michael Meissner wrote:
> 
>             However, the double pattern is completely broken.  This cannot go in.
> 
>         [snip]
> 
>             It is unacceptable to have to do the inner loop doing a load, vector add, and
>             store in the loop.
> 
>         Before the patch, the final reduction used *vsx_reduc_splus_v2df; after
>         the patch, it is *vsx_reduc_plus_v2df_scalar.  The former does a vector
>         add, the latter a float add.  And it uses the same pseudoregister for the
>         accumulator throughout.  IRA decides a register is more expensive than
>         memory for this, I suppose because it wants both V2DF and DF?  It doesn't
>         seem to like the subreg very much.
> 
>         The new code does look nicer otherwise :-)
> 
> 
>         Segher
-------------- next part --------------
A non-text attachment was scrubbed...
Name: vec_rs6000_combined.patch
Type: text/x-patch
Size: 4597 bytes
Desc: not available
URL: <http://gcc.gnu.org/pipermail/gcc-patches/attachments/20141211/2dfb862e/attachment.bin>


More information about the Gcc-patches mailing list