Next: , Previous: , Up: Function Attributes   [Contents][Index]


6.31.23 PowerPC Function Attributes

These function attributes are supported by the PowerPC back end:

longcall
shortcall

The longcall attribute indicates that the function might be far away from the call site and require a different (more expensive) calling sequence. The shortcall attribute indicates that the function is always close enough for the shorter calling sequence to be used. These attributes override both the -mlongcall switch and the #pragma longcall setting.

See RS/6000 and PowerPC Options, for more information on whether long calls are necessary.

target (options)

As discussed in Common Function Attributes, this attribute allows specification of target-specific compilation options.

On the PowerPC, the following options are allowed:

altivec
no-altivec

Generate code that uses (does not use) AltiVec instructions. In 32-bit code, you cannot enable AltiVec instructions unless -mabi=altivec is used on the command line.

cmpb
no-cmpb

Generate code that uses (does not use) the compare bytes instruction implemented on the POWER6 processor and other processors that support the PowerPC V2.05 architecture.

dlmzb
no-dlmzb

Generate code that uses (does not use) the string-search ‘dlmzb’ instruction on the IBM 405, 440, 464 and 476 processors. This instruction is generated by default when targeting those processors.

fprnd
no-fprnd

Generate code that uses (does not use) the FP round to integer instructions implemented on the POWER5+ processor and other processors that support the PowerPC V2.03 architecture.

hard-dfp
no-hard-dfp

Generate code that uses (does not use) the decimal floating-point instructions implemented on some POWER processors.

isel
no-isel

Generate code that uses (does not use) ISEL instruction.

mfcrf
no-mfcrf

Generate code that uses (does not use) the move from condition register field instruction implemented on the POWER4 processor and other processors that support the PowerPC V2.01 architecture.

mfpgpr
no-mfpgpr

Generate code that uses (does not use) the FP move to/from general purpose register instructions implemented on the POWER6X processor and other processors that support the extended PowerPC V2.05 architecture.

mulhw
no-mulhw

Generate code that uses (does not use) the half-word multiply and multiply-accumulate instructions on the IBM 405, 440, 464 and 476 processors. These instructions are generated by default when targeting those processors.

multiple
no-multiple

Generate code that uses (does not use) the load multiple word instructions and the store multiple word instructions.

update
no-update

Generate code that uses (does not use) the load or store instructions that update the base register to the address of the calculated memory location.

popcntb
no-popcntb

Generate code that uses (does not use) the popcount and double-precision FP reciprocal estimate instruction implemented on the POWER5 processor and other processors that support the PowerPC V2.02 architecture.

popcntd
no-popcntd

Generate code that uses (does not use) the popcount instruction implemented on the POWER7 processor and other processors that support the PowerPC V2.06 architecture.

powerpc-gfxopt
no-powerpc-gfxopt

Generate code that uses (does not use) the optional PowerPC architecture instructions in the Graphics group, including floating-point select.

powerpc-gpopt
no-powerpc-gpopt

Generate code that uses (does not use) the optional PowerPC architecture instructions in the General Purpose group, including floating-point square root.

recip-precision
no-recip-precision

Assume (do not assume) that the reciprocal estimate instructions provide higher-precision estimates than is mandated by the PowerPC ABI.

string
no-string

Generate code that uses (does not use) the load string instructions and the store string word instructions to save multiple registers and do small block moves.

vsx
no-vsx

Generate code that uses (does not use) vector/scalar (VSX) instructions, and also enable the use of built-in functions that allow more direct access to the VSX instruction set. In 32-bit code, you cannot enable VSX or AltiVec instructions unless -mabi=altivec is used on the command line.

friz
no-friz

Generate (do not generate) the friz instruction when the -funsafe-math-optimizations option is used to optimize rounding a floating-point value to 64-bit integer and back to floating point. The friz instruction does not return the same value if the floating-point number is too large to fit in an integer.

avoid-indexed-addresses
no-avoid-indexed-addresses

Generate code that tries to avoid (not avoid) the use of indexed load or store instructions.

paired
no-paired

Generate code that uses (does not use) the generation of PAIRED simd instructions.

longcall
no-longcall

Generate code that assumes (does not assume) that all calls are far away so that a longer more expensive calling sequence is required.

cpu=CPU

Specify the architecture to generate code for when compiling the function. If you select the target("cpu=power7") attribute when generating 32-bit code, VSX and AltiVec instructions are not generated unless you use the -mabi=altivec option on the command line.

tune=TUNE

Specify the architecture to tune for when compiling the function. If you do not specify the target("tune=TUNE") attribute and you do specify the target("cpu=CPU") attribute, compilation tunes for the CPU architecture, and not the default tuning specified on the command line.

On the PowerPC, the inliner does not inline a function that has different target options than the caller, unless the callee has a subset of the target options of the caller.


Next: , Previous: , Up: Function Attributes   [Contents][Index]