Next: , Previous: , Up: Compiler Switches   [Contents][Index]


4.3.5 Validity Checking

The Ada Reference Manual defines the concept of invalid values (see RM 13.9.1). The primary source of invalid values is uninitialized variables. A scalar variable that is left uninitialized may contain an invalid value; the concept of invalid does not apply to access or composite types.

It is an error to read an invalid value, but the RM does not require run-time checks to detect such errors, except for some minimal checking to prevent erroneous execution (i.e. unpredictable behavior). This corresponds to the `-gnatVd' switch below, which is the default. For example, by default, if the expression of a case statement is invalid, it will raise Constraint_Error rather than causing a wild jump, and if an array index on the left-hand side of an assignment is invalid, it will raise Constraint_Error rather than overwriting an arbitrary memory location.

The `-gnatVa' may be used to enable additional validity checks, which are not required by the RM. These checks are often very expensive (which is why the RM does not require them). These checks are useful in tracking down uninitialized variables, but they are not usually recommended for production builds, and in particular we do not recommend using these extra validity checking options in combination with optimization, since this can confuse the optimizer. If performance is a consideration, leading to the need to optimize, then the validity checking options should not be used.

The other `-gnatV'x switches below allow finer-grained control; you can enable whichever validity checks you desire. However, for most debugging purposes, `-gnatVa' is sufficient, and the default `-gnatVd' (i.e. standard Ada behavior) is usually sufficient for non-debugging use.

The `-gnatB' switch tells the compiler to assume that all values are valid (that is, within their declared subtype range) except in the context of a use of the Valid attribute. This means the compiler can generate more efficient code, since the range of values is better known at compile time. However, an uninitialized variable can cause wild jumps and memory corruption in this mode.

The `-gnatV'x switch allows control over the validity checking mode as described below. The x argument is a string of letters that indicate validity checks that are performed or not performed in addition to the default checks required by Ada as described above.

-gnatVa

`All validity checks.'

All validity checks are turned on. That is, `-gnatVa' is equivalent to `gnatVcdfimorst'.

-gnatVc

`Validity checks for copies.'

The right hand side of assignments, and the initializing values of object declarations are validity checked.

-gnatVd

`Default (RM) validity checks.'

Some validity checks are done by default following normal Ada semantics (RM 13.9.1 (9-11)). A check is done in case statements that the expression is within the range of the subtype. If it is not, Constraint_Error is raised. For assignments to array components, a check is done that the expression used as index is within the range. If it is not, Constraint_Error is raised. Both these validity checks may be turned off using switch `-gnatVD'. They are turned on by default. If `-gnatVD' is specified, a subsequent switch `-gnatVd' will leave the checks turned on. Switch `-gnatVD' should be used only if you are sure that all such expressions have valid values. If you use this switch and invalid values are present, then the program is erroneous, and wild jumps or memory overwriting may occur.

-gnatVe

`Validity checks for elementary components.'

In the absence of this switch, assignments to record or array components are not validity checked, even if validity checks for assignments generally (`-gnatVc') are turned on. In Ada, assignment of composite values do not require valid data, but assignment of individual components does. So for example, there is a difference between copying the elements of an array with a slice assignment, compared to assigning element by element in a loop. This switch allows you to turn off validity checking for components, even when they are assigned component by component.

-gnatVf

`Validity checks for floating-point values.'

In the absence of this switch, validity checking occurs only for discrete values. If `-gnatVf' is specified, then validity checking also applies for floating-point values, and NaNs and infinities are considered invalid, as well as out of range values for constrained types. Note that this means that standard IEEE infinity mode is not allowed. The exact contexts in which floating-point values are checked depends on the setting of other options. For example, `-gnatVif' or `-gnatVfi' (the order does not matter) specifies that floating-point parameters of mode in should be validity checked.

-gnatVi

`Validity checks for ‘in‘ mode parameters.'

Arguments for parameters of mode in are validity checked in function and procedure calls at the point of call.

-gnatVm

`Validity checks for ‘in out‘ mode parameters.'

Arguments for parameters of mode in out are validity checked in procedure calls at the point of call. The ’m’ here stands for modify, since this concerns parameters that can be modified by the call. Note that there is no specific option to test out parameters, but any reference within the subprogram will be tested in the usual manner, and if an invalid value is copied back, any reference to it will be subject to validity checking.

-gnatVn

`No validity checks.'

This switch turns off all validity checking, including the default checking for case statements and left hand side subscripts. Note that the use of the switch `-gnatp' suppresses all run-time checks, including validity checks, and thus implies `-gnatVn'. When this switch is used, it cancels any other `-gnatV' previously issued.

-gnatVo

`Validity checks for operator and attribute operands.'

Arguments for predefined operators and attributes are validity checked. This includes all operators in package Standard, the shift operators defined as intrinsic in package Interfaces and operands for attributes such as Pos. Checks are also made on individual component values for composite comparisons, and on the expressions in type conversions and qualified expressions. Checks are also made on explicit ranges using .. (e.g., slices, loops etc).

-gnatVp

`Validity checks for parameters.'

This controls the treatment of parameters within a subprogram (as opposed to `-gnatVi' and `-gnatVm' which control validity testing of parameters on a call. If either of these call options is used, then normally an assumption is made within a subprogram that the input arguments have been validity checking at the point of call, and do not need checking again within a subprogram). If `-gnatVp' is set, then this assumption is not made, and parameters are not assumed to be valid, so their validity will be checked (or rechecked) within the subprogram.

-gnatVr

`Validity checks for function returns.'

The expression in return statements in functions is validity checked.

-gnatVs

`Validity checks for subscripts.'

All subscripts expressions are checked for validity, whether they appear on the right side or left side (in default mode only left side subscripts are validity checked).

-gnatVt

`Validity checks for tests.'

Expressions used as conditions in if, while or exit statements are checked, as well as guard expressions in entry calls.

The `-gnatV' switch may be followed by a string of letters to turn on a series of validity checking options. For example, -gnatVcr specifies that in addition to the default validity checking, copies and function return expressions are to be validity checked. In order to make it easier to specify the desired combination of effects, the upper case letters CDFIMORST may be used to turn off the corresponding lower case option. Thus -gnatVaM turns on all validity checking options except for checking of **in out** procedure arguments.

The specification of additional validity checking generates extra code (and in the case of `-gnatVa' the code expansion can be substantial). However, these additional checks can be very useful in detecting uninitialized variables, incorrect use of unchecked conversion, and other errors leading to invalid values. The use of pragma Initialize_Scalars is useful in conjunction with the extra validity checking, since this ensures that wherever possible uninitialized variables have invalid values.

See also the pragma Validity_Checks which allows modification of the validity checking mode at the program source level, and also allows for temporary disabling of validity checks.


Next: , Previous: , Up: Compiler Switches   [Contents][Index]