-mmangle-cpu -mcpu=@var{cpu} -mtext=@var{text section}
-mdata=@var{data section} -mrodata=@var{readonly data section}
+@emph{TMS320C3x/C4x Options}
+-mcpu=@var{cpu} -mbig -msmall -mregparm -mmemparm
+-mfast-fix -mmpyi -mbk -mti -mdp-isr-reload
+-mrpts=@var{count} -mrptb -mdb -mloop-unsigned
+-mparallel-insns -mparallel-mpy -mpreserve-float
+
@emph{V850 Options}
-mlong-calls -mno-long-calls -mep -mno-ep
-mprolog-function -mno-prolog-function -mspace
* H8/300 Options::
* SH Options::
* System V Options::
+* TMS320C3x/C4x Options::
* V850 Options::
* ARC Options::
* NS32K Options::
@c the generic assembler that comes with Solaris takes just -Ym.
@end table
+@node TMS320C3x/C4x Options
+@subsection TMS320C3x/C4x Options
+@cindex TMS320C3x/C4x Options
+
+These @samp{-m} options are defined for TMS320C3x/C4x implementations:
+
+@table @code
+
+@item -mcpu=@var{cpu_type}
+Set the instruction set, register set, and instruction scheduling
+parameters for machine type @var{cpu_type}. Supported values for
+@var{cpu_type} are @samp{c30}, @samp{c31}, @samp{c32}, @samp{c40}, and
+@samp{c44}. The default is @samp{c40} to generate code for the
+TMS320C40.
+
+@item -mbig-memory
+@item -mbig
+@itemx -msmall-memory
+@itemx -msmall
+Generates code for the big or small memory model. The small memory
+model assumed that all data fits into one 64K word page. At run-time
+the data page (DP) register must be set to point to the 64K page
+containing the .bss and .data program sections. The big memory model is
+the default and requires reloading of the DP register for every direct
+memory access.
+
+@item -mbk
+@itemx -mno-bk
+Allow (disallow) allocation of general integer operands into the block
+count register BK.
+
+@item -mdb
+@itemx -mno-db
+Enable (disable) generation of code using decrement and branch,
+DBcond(D), instructions. This is enabled by default for the C4x. To be
+on the safe side, this is disabled for the C3x, since the maximum
+iteration count on the C3x is 2^23 + 1 (but who iterates loops more than
+2^23 times on the C3x?). Note that GCC will try to reverse a loop so
+that it can utilise the decrement and branch instruction, but will give
+up if there is more than one memory reference in the loop. Thus a loop
+where the loop counter is decremented can generate slightly more
+efficient code, in cases where the RPTB instruction cannot be utilised.
+
+@item -mdp-isr-reload
+@itemx -mparanoid
+Force the DP register to be saved on entry to an interrupt service
+routine (ISR), reloaded to point to the data section, and restored on
+exit from the ISR. This should not be required unless someone has
+violated the small memory model by modifying the DP register, say within
+an object library.
+
+@item -mmpyi
+@itemx -mno-mpyi
+For the C3x use the 24-bit MPYI instruction for integer multiplies
+instead of a library call to guarantee 32-bit results. Note that if one
+of the operands is a constant, then the multiplication will be performed
+using shifts and adds. If the -mmpyi option is not specified for the C3x,
+then squaring operations are performed inline instead of a library call.
+
+@item -mfast-fix
+@itemx -mno-fast-fix
+The C3x/C4x FIX instruction to convert a floating point value to an
+integer value chooses the nearest integer less than or equal to the
+floating point value rather than to the nearest integer. Thus if the
+floating point number is negative, the result will be incorrectly
+truncated an additional code is necessary to detect and correct this
+case. This option can be used to disable generation of the additional
+code required to correct the result.
+
+@item -mrptb
+@itemx -mno-rptb
+Enable (disable) generation of repeat block sequences using the RPTB
+instruction for zero overhead looping. The RPTB construct is only used
+for innermost loops that do not call functions or jump across the loop
+boundaries. There is no advantage having nested RPTB loops due to the
+overhead required to save and restore the RC, RS, and RE registers.
+This is enabled by default with -O2.
+
+@item -mrpts=@var{count}
+@itemx -mno-rpts
+Enable (disable) the use of the single instruction repeat instruction
+RPTS. If a repeat block contains a single instruction, and the loop
+count can be guaranteed to be less than the value @var{count}, GCC will
+emit a RPTS instruction instead of a RPTB. If no value is specified,
+then a RPTS will be emitted even if the loop count cannot be determined
+at compile time. Note that the repeated instruction following RPTS does
+not have to be reloaded from memory each iteration, thus freeing up the
+CPU buses for oeprands. However, since interrupts are blocked by this
+instruction, it is disabled by default.
+
+@item -mloop-unsigned
+@itemx -mno-loop-unsigned
+The maximum iteration count when using RPTS and RPTB (and DB on the C40)
+is 2^31 + 1 since these instructions test if the iteration count is
+negative to terminate the loop. If the iteration count is unsigned
+there is a possibility than the 2^31 + 1 maximum iteration count may be
+exceeded. This switch allows an unsigned iteration count.
+
+@item -mti
+Try to emit an assembler syntax that the TI assembler (asm30) is happy
+with. This also enforces compatibility with the API employed by the TI
+C3x C compiler. For example, long doubles are passed as structures
+rather than in floating point registers.
+
+@item -mregparm
+@itemx -mmemparm
+Generate code that uses registers (stack) for passing arguments to functions.
+By default, arguments are passed in registers where possible rather
+than by pushing arguments on to the stack.
+
+@item -mparallel-insns
+@itemx -mno-parallel-insns
+Allow the generation of parallel instructions. This is enabled by
+default with -O2.
+
+@item -mparallel-mpy
+@itemx -mno-parallel-mpy
+Allow the generation of MPY||ADD and MPY||SUB parallel instructions,
+provided -mparallel-insns is also specified. These instructions have
+tight register constraints which can pessimize the code generation
+of large functions.
+
+@end table
+
@node V850 Options
@subsection V850 Options
@cindex V850 Options
git://gcc.gnu.org / gcc.git / commitdiff