This section discusses the macros that describe which kinds of values (specifically, which machine modes) each register can hold, and how many consecutive registers are needed for a given mode.
This hook returns the number of consecutive hard registers, starting
at register number regno, required to hold a value of mode
mode. This hook must never return zero, even if a register
cannot hold the requested mode - indicate that with
The default definition returns the number of words in mode.
A C expression that is nonzero if a value of mode mode, stored
in memory, ends with padding that causes it to take up more space than
in registers starting at register number regno (as determined by
multiplying GCC’s notion of the size of the register when containing
this mode by the number of registers returned by
TARGET_HARD_REGNO_NREGS). By default this is zero.
For example, if a floating-point value is stored in three 32-bit registers but takes up 128 bits in memory, then this would be nonzero.
This macros only needs to be defined if there are cases where
would otherwise wrongly determine that a
subreg can be
represented by an offset to the register number, when in fact such a
subreg would contain some of the padding not stored in
registers and so not be representable.
For values of regno and mode for which
HARD_REGNO_NREGS_HAS_PADDING returns nonzero, a C expression
returning the greater number of registers required to hold the value
including any padding. In the example above, the value would be four.
Define this macro if the natural size of registers that hold values of mode mode is not the word size. It is a C expression that should give the natural size in bytes for the specified mode. It is used by the register allocator to try to optimize its results. This happens for example on SPARC 64-bit where the natural size of floating-point registers is still 32-bit.
This hook returns true if it is permissible to store a value of mode mode in hard register number regno (or in several registers starting with that one). The default definition returns true unconditionally.
You need not include code to check for the numbers of fixed registers, because the allocation mechanism considers them to be always occupied.
On some machines, double-precision values must be kept in even/odd register pairs. You can implement that by defining this hook to reject odd register numbers for such modes.
The minimum requirement for a mode to be OK in a register is that the ‘movmode’ instruction pattern support moves between the register and other hard register in the same class and that moving a value into the register and back out not alter it.
Since the same instruction used to move
word_mode will work for
all narrower integer modes, it is not necessary on any machine for
this hook to distinguish between these modes, provided you define
patterns ‘movhi’, etc., to take advantage of this. This is
useful because of the interaction between
TARGET_MODES_TIEABLE_P; it is very desirable for all integer
modes to be tieable.
Many machines have special registers for floating point arithmetic. Often people assume that floating point machine modes are allowed only in floating point registers. This is not true. Any registers that can hold integers can safely hold a floating point machine mode, whether or not floating arithmetic can be done on it in those registers. Integer move instructions can be used to move the values.
On some machines, though, the converse is true: fixed-point machine
modes may not go in floating registers. This is true if the floating
registers normalize any value stored in them, because storing a
non-floating value there would garble it. In this case,
TARGET_HARD_REGNO_MODE_OK should reject fixed-point machine modes in
floating registers. But if the floating registers do not automatically
normalize, if you can store any bit pattern in one and retrieve it
unchanged without a trap, then any machine mode may go in a floating
register, so you can define this hook to say so.
The primary significance of special floating registers is rather that
they are the registers acceptable in floating point arithmetic
instructions. However, this is of no concern to
TARGET_HARD_REGNO_MODE_OK. You handle it by writing the proper
constraints for those instructions.
On some machines, the floating registers are especially slow to access,
so that it is better to store a value in a stack frame than in such a
register if floating point arithmetic is not being done. As long as the
floating registers are not in class
GENERAL_REGS, they will not
be used unless some pattern’s constraint asks for one.
A C expression that is nonzero if it is OK to rename a hard register from to another hard register to.
One common use of this macro is to prevent renaming of a register to another register that is not saved by a prologue in an interrupt handler.
The default is always nonzero.
This hook returns true if a value of mode mode1 is accessible in mode mode2 without copying.
TARGET_HARD_REGNO_MODE_OK (r, mode1) and
TARGET_HARD_REGNO_MODE_OK (r, mode2) are always
the same for any r, then
TARGET_MODES_TIEABLE_P (mode1, mode2)
should be true. If they differ for any r, you should define
this hook to return false unless some other mechanism ensures the
accessibility of the value in a narrower mode.
You should define this hook to return true in as many cases as possible since doing so will allow GCC to perform better register allocation. The default definition returns true unconditionally.
This target hook should return
true if it is OK to use a hard register
regno as scratch reg in peephole2.
One common use of this macro is to prevent using of a register that is not saved by a prologue in an interrupt handler.
The default version of this hook always returns
Define this macro if the compiler should avoid copies to/from
registers. You should only define this macro if support for copying to/from
CCmode is incomplete.