-march=
arch- Generate code that will run on arch, which can be the name of a
generic MIPS ISA, or the name of a particular processor. The ISA names
are: mips1, mips2, mips3, mips4, mips32
and mips64. The processor names are: r2000,
r3000, r3900, r4000, vr4100, vr4300,
r4400, r4600, r4650, vr5000, r6000,
r8000, 4kc, 4kp, 5kc, 20kc,
orion, and sb1. The special value from-abi selects the
most compatible architecture for the selected ABI (that is,
mips1 for 32-bit ABIs and mips3 for 64-bit ABIs).
In processor names, a final 000 can be abbreviated as k
(for example, -march=r2k). Prefixes are optional, and
vr may be written r.
GCC defines two macros based on the value of this option. The first
is _MIPS_ARCH, which gives the name of target architecture, as
a string. The second has the form _MIPS_ARCH_foo,
where foo is the capitalized value of _MIPS_ARCH.
For example, -march=r2000 will set _MIPS_ARCH
to "r2000" and define the macro _MIPS_ARCH_R2000.
Note that the _MIPS_ARCH macro uses the processor names given
above. In other words, it will have the full prefix and will not
abbreviate 000 as k. In the case of from-abi,
the macro names the resolved architecture (either "mips1" or
"mips3"). It names the default architecture when no
-march option is given.
-mtune=
arch- Optimize for arch. Among other things, this option controls
the way instructions are scheduled, and the perceived cost of arithmetic
operations. The list of arch values is the same as for
-march.
When this option is not used, GCC will optimize for the processor
specified by -march. By using -march and
-mtune together, it is possible to generate code that will
run on a family of processors, but optimize the code for one
particular member of that family.
-mtune defines the macros _MIPS_TUNE and
_MIPS_TUNE_foo, which work in the same way as the
-march ones described above.
-mips1
- Equivalent to -march=mips1.
-mips2
- Equivalent to -march=mips2.
-mips3
- Equivalent to -march=mips3.
-mips4
- Equivalent to -march=mips4.
-mips32
- Equivalent to -march=mips32.
-mips64
- Equivalent to -march=mips64.
-mfused-madd
-mno-fused-madd
- Generate code that uses (does not use) the floating point multiply and
accumulate instructions, when they are available. These instructions
are generated by default if they are available, but this may be
undesirable if the extra precision causes problems or on certain chips
in the mode where denormals are rounded to zero where denormals
generated by multiply and accumulate instructions cause exceptions
anyway.
-mfp32
- Assume that floating point registers are 32 bits wide.
-mfp64
- Assume that floating point registers are 64 bits wide.
-mgp32
- Assume that general purpose registers are 32 bits wide.
-mgp64
- Assume that general purpose registers are 64 bits wide.
-mint64
- Force int and long types to be 64 bits wide. See -mlong32 for an
explanation of the default, and the width of pointers.
-mlong64
- Force long types to be 64 bits wide. See -mlong32 for an
explanation of the default, and the width of pointers.
-mlong32
- Force long, int, and pointer types to be 32 bits wide.
The default size of ints, longs and pointers depends on the ABI. All
the supported ABIs use 32-bit ints. The n64 ABI uses 64-bit longs, as
does the 64-bit Cygnus EABI; the others use 32-bit longs. Pointers
are the same size as longs, or the same size as integer registers,
whichever is smaller.
-mabi=32
-mabi=o64
-mabi=n32
-mabi=64
-mabi=eabi
-mabi=meabi
- Generate code for the given ABI.
Note that there are two embedded ABIs: -mabi=eabi
selects the one defined by Cygnus while -meabi=meabi
selects the one defined by MIPS. Both these ABIs have
32-bit and 64-bit variants. Normally, GCC will generate
64-bit code when you select a 64-bit architecture, but you
can use -mgp32 to get 32-bit code instead.
-mmips-as
- Generate code for the MIPS assembler, and invoke mips-tfile to
add normal debug information. This is the default for all
platforms except for the OSF/1 reference platform, using the OSF/rose
object format. If the either of the -gstabs or -gstabs+
switches are used, the mips-tfile program will encapsulate the
stabs within MIPS ECOFF.
-mgas
- Generate code for the GNU assembler. This is the default on the OSF/1
reference platform, using the OSF/rose object format. Also, this is
the default if the configure option --with-gnu-as is used.
-msplit-addresses
-mno-split-addresses
- Generate code to load the high and low parts of address constants separately.
This allows GCC to optimize away redundant loads of the high order
bits of addresses. This optimization requires GNU as and GNU ld.
This optimization is enabled by default for some embedded targets where
GNU as and GNU ld are standard.
-mrnames
-mno-rnames
- The -mrnames switch says to output code using the MIPS software
names for the registers, instead of the hardware names (ie, a0
instead of $4). The only known assembler that supports this option
is the Algorithmics assembler.
-mgpopt
-mno-gpopt
- The -mgpopt switch says to write all of the data declarations
before the instructions in the text section, this allows the MIPS
assembler to generate one word memory references instead of using two
words for short global or static data items. This is on by default if
optimization is selected.
-mstats
-mno-stats
- For each non-inline function processed, the -mstats switch
causes the compiler to emit one line to the standard error file to
print statistics about the program (number of registers saved, stack
size, etc.).
-mmemcpy
-mno-memcpy
- The -mmemcpy switch makes all block moves call the appropriate
string function (memcpy or bcopy) instead of possibly
generating inline code.
-mmips-tfile
-mno-mips-tfile
- The -mno-mips-tfile switch causes the compiler not
postprocess the object file with the mips-tfile program,
after the MIPS assembler has generated it to add debug support. If
mips-tfile is not run, then no local variables will be
available to the debugger. In addition, stage2 and
stage3 objects will have the temporary file names passed to the
assembler embedded in the object file, which means the objects will
not compare the same. The -mno-mips-tfile switch should only
be used when there are bugs in the mips-tfile program that
prevents compilation.
-msoft-float
- Generate output containing library calls for floating point.
Warning: the requisite libraries are not part of GCC.
Normally the facilities of the machine's usual C compiler are used, but
this can't be done directly in cross-compilation. You must make your
own arrangements to provide suitable library functions for
cross-compilation.
-mhard-float
- Generate output containing floating point instructions. This is the
default if you use the unmodified sources.
-mabicalls
-mno-abicalls
- Emit (or do not emit) the pseudo operations .abicalls,
.cpload, and .cprestore that some System V.4 ports use for
position independent code.
-mlong-calls
-mno-long-calls
- Do all calls with the JALR instruction, which requires
loading up a function's address into a register before the call.
You need to use this switch, if you call outside of the current
512 megabyte segment to functions that are not through pointers.
-mhalf-pic
-mno-half-pic
- Put pointers to extern references into the data section and load them
up, rather than put the references in the text section.
-membedded-pic
-mno-embedded-pic
- Generate PIC code suitable for some embedded systems. All calls are
made using PC relative address, and all data is addressed using the $gp
register. No more than 65536 bytes of global data may be used. This
requires GNU as and GNU ld which do most of the work. This currently
only works on targets which use ECOFF; it does not work with ELF.
-membedded-data
-mno-embedded-data
- Allocate variables to the read-only data section first if possible, then
next in the small data section if possible, otherwise in data. This gives
slightly slower code than the default, but reduces the amount of RAM required
when executing, and thus may be preferred for some embedded systems.
-muninit-const-in-rodata
-mno-uninit-const-in-rodata
- When used together with -membedded-data, it will always store uninitialized
const variables in the read-only data section.
-msingle-float
-mdouble-float
- The -msingle-float switch tells gcc to assume that the floating
point coprocessor only supports single precision operations, as on the
r4650 chip. The -mdouble-float switch permits gcc to use
double precision operations. This is the default.
-mmad
-mno-mad
- Permit use of the mad, madu and mul instructions,
as on the r4650 chip.
-m4650
- Turns on -msingle-float, -mmad, and, at least for now,
-mcpu=r4650.
-mips16
-mno-mips16
- Enable 16-bit instructions.
-mentry
- Use the entry and exit pseudo ops. This option can only be used with
-mips16.
-EL
- Compile code for the processor in little endian mode.
The requisite libraries are assumed to exist.
-EB
- Compile code for the processor in big endian mode.
The requisite libraries are assumed to exist.
-G
num- Put global and static items less than or equal to num bytes into
the small data or bss sections instead of the normal data or bss
section. This allows the assembler to emit one word memory reference
instructions based on the global pointer (gp or $28),
instead of the normal two words used. By default, num is 8 when
the MIPS assembler is used, and 0 when the GNU assembler is used. The
-G num switch is also passed to the assembler and linker.
All modules should be compiled with the same -G num
value.
-nocpp
- Tell the MIPS assembler to not run its preprocessor over user
assembler files (with a .s suffix) when assembling them.
-mfix7000
- Pass an option to gas which will cause nops to be inserted if
the read of the destination register of an mfhi or mflo instruction
occurs in the following two instructions.
-no-crt0
- Do not include the default crt0.
-mflush-func=
func-mno-flush-func
- Specifies the function to call to flush the I and D caches, or to not
call any such function. If called, the function must take the same
arguments as the common
_flush_func()
, that is, the address of the
memory range for which the cache is being flushed, the size of the
memory range, and the number 3 (to flush both caches). The default
depends on the target gcc was configured for, but commonly is either
_flush_func or __cpu_flush.
-mbranch-likely
-mno-branch-likely
- Enable or disable use of Branch Likely instructions, regardless of the
default for the selected architecture. By default, Branch Likely
instructions may be generated if they are supported by the selected
architecture. An exception is for the MIPS32 and MIPS64 architectures
and processors which implement those architectures; for those, Branch
Likely instructions will not be generated by default because the MIPS32
and MIPS64 architectures specifically deprecate their use.